White Redarc mounting bracket seen from above, the plate with a central cut-out, a folded tang and two mounting feet at the corners

Stainless Redarc mounting bracket with a horizontal shelf carrying a large round hole and a set of fixing holes, meeting an upright plate with a rectangular cut-out

Stainless Redarc mounting bracket with a long flat foot bolted across the base, the upright plate carrying a rectangular cut-out and a slot at the top

Stainless Redarc mounting bracket standing upright, a tall plate with a rectangular cut-out folding to a curved top flange and a slotted foot at the base

Stainless Redarc mounting bracket at an angle, the plate with a rectangular cut-out and a curved side wing, with two small tabs folded out along the lower edge

Stainless Redarc mounting bracket marked BCDCMB-006, a plate with a large rectangular cut-out, a folded retaining tang and two mounting feet, one with a large round hole

Stainless Redarc mounting bracket seen from the front quarter, the upright plate with a cut-out and a top flange carrying two slots and a row of fixing holes

Stainless Redarc mounting bracket standing on edge, the plate with a rectangular cut-out and two upright tabs, with a curved arm reaching out to a slotted mounting eye

Stainless Redarc mounting bracket viewed from above, the cut-out plate with a folded retaining tang and two slotted feet at opposite corners

Stainless Redarc mounting bracket in a stepped form, an upper platform with a slot and a lower plate with a rectangular cut-out, joined by a folded riser with a side wing

White Redarc mounting bracket shown with its two separate white support arms laid out either side

White Redarc mounting bracket seen from above, a flat plate with slotted and round fixing holes, a raised centre section and turned-down edges at each end

White Redarc mounting bracket viewed edge on, the tall plate with a rectangular cut-out folding to a small top flange and a slotted foot at the bottom

White powder-coated Redarc mounting bracket with a rectangular cut-out for the charger, a folded side wing with fixing holes and a hooked tab at the bottom edge

White Redarc mounting bracket seen from a low angle, the cut-out plate with a hooked tab and two slotted feet turned toward the camera

White Redarc mounting bracket at an angle, the plate with a central cut-out and two retaining tangs, with slotted feet at opposite corners

White Redarc mounting bracket at a shallow angle, a plate with a central cut-out, a hooked retaining tab and two slotted mounting feet

Stainless Redarc mounting bracket photographed against white, the cut-out plate with two upright tabs and a curved arm reaching to a slotted mounting eye

Tall white Redarc mounting bracket, a narrow plate with two cut-outs stacked one above the other, a folded side flange and an arm reaching out to a slotted mounting eye

Redarc

BCDC Mounting Brackets — Vehicle-Specific & Universal

BCDCMB-103

Powder-coated stainless mounting brackets that bolt a Redarc BCDC Classic or Alpha charger onto 13 vehicle-specific factory mounting points, or anywhere with the universal plate.

$99.00

4 interest-free payments of $24.75 with Afterpay

or finance your build with Allied Finance

Vehicle

We accept Visa Mastercard Amex Apple Pay PayPal Zip Afterpay Finance

Variant-specific fitment — pick the bracket for your vehicle:

Shipping & collection

Worldwide shipping available^*

In-store pickup

Professional installation available

*Shipping is calculated at checkout based on your location. Some products can't be delivered to every address.

FITS ANY REDARC BCDC

Purpose-built brackets for every BCDC in the current Redarc range.

VEHICLE-SPECIFIC OR UNIVERSAL

Choose from vehicle-specific fit or universal mounting options for the common install locations.

POWDER-COATED STEEL

Heavy-duty steel bracket, powder-coated for corrosion resistance.

ALL FASTENERS INCLUDED

Install-ready — all bolts, nuts and washers included in the kit.

2 YEAR REDARC WARRANTY

Backed by 2 years direct from Redarc. Repair or replacement in accordance with Redarc's warranty policy.

Stainless mounting brackets that bolt a Redarc BCDC charger onto existing factory mounting points in the engine bay. Thirteen variants cover Prado 150, LandCruiser 70, J100, J105, 200 and 300 Series, Hilux N70 and N80, Isuzu D-MAX RT, Holden Colorado RG, Triton MR, Pajero QF, Patrol Y61 GU and the Ford Ranger, Everest and Volkswagen Amarok Next Gen V6 platforms, with a universal option for anything else.

Each bracket is laser-cut powder-coated stainless with a hooked retaining tab, slotted feet and a central cut-out sized to the charger's housing. Factory bolt holes line up straight, so there's no drilling and no custom fabrication. Fasteners pack with every bracket, and the design positions the charger forward in the engine bay for airflow during long runs.

Fits both the BCDC Classic range (Classic25 and Classic40) and the BCDC Alpha range (Alpha25, Alpha50 and Alpha75). The two ranges use different bolt lengths, so pack the matching bolt kit with the charger. Not compatible with the BCDC Core range (BCDCN1225 and BCDCN1240).

What sets it apart

Factory mounting points — no drilling, no custom brackets, no cutting panels.

Vehicle-specific design — 13 variants plus universal, each engineered for one platform.

Powder-coated stainless — corrosion resistant through dust, water and salt spray.

Charger-forward airflow — positions the heat sink where the engine bay moves the most air.

Classic and Alpha compatible — one bracket pattern covers both BCDC ranges with the correct bolt kit.

Fasteners and instructions included — nothing else to source for the install.

Australian designed and made — built in Lonsdale, South Australia.

Backed by 2-year Redarc warranty — manufacturer warranty, direct from Redarc.

Factory mounting points — no drilling, no custom brackets, no cutting.
Vehicle-specific design — 13 variants plus universal, one per platform.
Powder-coated stainless — corrosion resistant through dust, water and salt spray.
Charger-forward airflow — heat sink sits where the engine bay moves the most air.
Classic and Alpha compatible — fits both BCDC ranges with the correct bolt kit.
Fasteners included — bracket, bolts and instructions pack together.
Australian designed and made — built in Lonsdale, South Australia.
2-year Redarc warranty — manufacturer warranty, direct from Redarc.

Build

Material: Stainless steel

Finish: Powder-coated white (current stock) or raw stainless (earlier stock)

Mounting: Factory bolt holes, vehicle-specific or universal

Fasteners: Included

Compatibility

Fits: BCDC Classic25, Classic40, Alpha25, Alpha50, Alpha75

Not compatible: BCDC Core (BCDCN1225, BCDCN1240)

Bolt kit: Classic M6×12mm, Alpha M6×20mm

Country of manufacture: Australia (Lonsdale, SA)

Variant-specific fitment — pick the bracket for your vehicle:

Toyota LandCruiser 200 Series (11/2008 onwards) — BCDCMB-101

Toyota LandCruiser 70 Series (03/2007–08/2023) — BCDCMB-102

Toyota Prado 150 Series (10/2009 onwards) — BCDCMB-103

Toyota Hilux N70 (03/2005–09/2015) — BCDCMB-104

Toyota Hilux N80 (10/2015 onwards) — BCDCMB-105

Isuzu D-MAX RT (06/2012–2019) / Holden Colorado RG (10/2015 onwards) — BCDCMB-106

Universal (anything else) — BCDCMB-107

Toyota LandCruiser J100 / J105 Series (1998–2007) — BCDCMB-108

Mitsubishi Triton MR / Pajero QF (2019 onwards) — BCDCMB-109

Nissan Patrol Y61 GU Series 4–9 — BCDCMB-110

Toyota LandCruiser 300 Series (2021 onwards) — BCDCMB-111

Ford Ranger / Everest Next Gen V6 (2022 onwards) / VW Amarok (03/2023 onwards) — BCDCMB-112

Toyota LandCruiser 70 Series V6 (09/2023 onwards) — BCDCMB-114

BCDC Core (BCDCN1225 / BCDCN1240) — not compatible with this bracket pattern; use the Core-specific mount.

Q: Which Redarc BCDC chargers fit this bracket?
A: Both the BCDC Classic range (Classic25 and Classic40) and the BCDC Alpha range (Alpha25, Alpha50 and Alpha75). The two ranges use different bolt lengths — M6×12mm for Classic, M6×20mm for Alpha — so pack the matching bolt kit with the charger. Not compatible with the BCDC Core range (BCDCN1225 and BCDCN1240).

Q: What does vehicle-specific actually mean here?
A: Each variant is laser-cut to line up with the factory bolt holes on that one platform. No drilling, no custom brackets, no cutting panels. The bracket bolts straight to the stock engine-bay mounting points on the vehicle it's cut for.

Q: My vehicle isn't on the list — what do I use?
A: Pick BCDCMB-107 (Universal). It's a flat plate with slotted and round fixing holes, a raised centre section and turned-down edges, designed to be bolted to any clear surface in the engine bay or on a canopy wall.

Q: What's included in the kit?
A: The bracket, all the mounting fasteners, and the fitting instructions for that variant. The BCDC charger itself is sold separately.

Q: Will it hold up in a working vehicle?
A: The bracket is stainless steel with a powder-coat finish, so it handles dust, water and salt spray without rusting out. Redarc backs it with a 2-year warranty against manufacturing defects.

Q: Where does the charger end up sitting?
A: Forward in the engine bay, with the heat sink positioned where airflow is strongest during continuous charging. Each bracket is designed to keep the charger clear of exhaust heat and in moving air.

Q: Can I install it myself?
A: The bracket side of the job is a bolt-on fit using factory mounting points, which is comfortably in DIY range with basic hand tools. Wiring the charger itself (fused battery feeds, cable sizing, isolator triggers) is where most installs want a qualified auto electrician — bring it to Elevate's workshop or any Redarc-authorised installer.

Q: Will this bracket fit the newer BCDC Core (BCDCN1225 or BCDCN1240)?
A: No. The BCDC Core range has a different housing footprint and uses a Core-specific mounting bracket. Only the Classic and Alpha BCDC ranges fit this bracket pattern.

Q: Is this a genuine Redarc product?
A: Yes. Designed, manufactured and warranted by Redarc from Lonsdale, South Australia. The 2-year warranty is a direct Redarc warranty, not a reseller warranty.

Q: What does the bracket actually weigh?
A: Around 4 to 4.7 kg depending on the variant — the more complex vehicle-specific brackets with wing supports (BCDCMB-108, 109, 110, 111, 112, 114) run heavier than the simpler plate variants.

Cart 0

Sorry, looks like we don't have enough of this product.