EA-Logo-RGB-Master_Yellow-Dark-Grey-Black


Currency

Cart 0

SIGN UP FOR $10 OFF YOUR FIRST ORDER

Sorry, looks like we don't have enough of this product.

Pair with
Estimate shipping
Add order notes
Is this a gift?
Subtotal Free
View cart
Shipping, taxes, and discount codes are calculated at checkout

Your Cart is Empty

Home / Lighting / Driving & light bars

6 Pin Deutsch DT Connector Kit — 13A Sealed

Elevate Automotive

6 Pin Deutsch DT Connector Kit — 13A Sealed

DT6

Sealed 6-pin Deutsch DT-series cable-to-cable connector kit. IP68, 13A per contact at 125°C. Matched housings, wedgelocks and 12 stamped terminals sized for 0.5-1.5mm² wire.

6 pin sealed
13A per contact
IP68 rated

$29.00

4 interest-free payments of $7.25 with
or finance your build with
We accept
Universal fitmentSealed cable-to-cable connector for auxiliary wiring, sensors and low-current DC circuits.

Shipping & collection

Worldwide shipping available*
In-store pickup
Professional installation available

*Shipping is calculated at checkout based on your location. Some products can't be delivered to every address.

A sealed 6-circuit Deutsch DT-series connector kit for building a waterproof cable-to-cable join anywhere on the vehicle. Runs 6-signal looms between engine and cabin, chassis and trailer, dashboard and roof console, or any harness section that has to survive water, dust, heat and vibration. Fits 4WD accessory looms, marine helm wiring, camper power distribution boxes, agricultural machinery and heavy-equipment harnesses.

Housings are DT-series thermoplastic with silicone perimeter and radial seals, rated IP68 mated and tested to 20G RMS vibration between 10 and 2000Hz. Contacts are size-16 stamped, rated 13A each at 125°C. The kit ships as a matched pair of housings, two wedgelocks and 12 terminals so a single order builds both ends of the join.

Crimp each terminal with a Deutsch-pattern indent crimper set to size-16; open-barrel automotive crimpers mash the barrel and the joint fails under vibration. Insert each terminal from the rear until it clicks, then push the wedge home from the front to lock. Seals only hold when the plug is fully mated and every unused cavity is plugged with a sealing plug; a half-locked join is not IP68.

  • 6 sealed circuits — every contact IP68 sealed
  • 13A per contact — signal or low-current power
  • 20G vibration — tested 10 to 2000Hz
  • Wedgelocks — secondary retention verifies seating
  • Complete kit — housings, wedges, all 12 contacts
  • Serviceable — pin-extraction tool releases and reuses terminals

Electrical

Series Deutsch DT

Pins 6

Contact rating 13A at 125°C

Wire size 0.5-1.5mm²

Environmental

Operating temp -55 to +125°C

Ingress IP68

Vibration 20G RMS

Materials

Housing Thermoplastic

Seal Silicone rubber

Contacts Stamped size-16

Length: 45.92mm

Width: 24.16mm

Height: 22.63mm

Weight: 0.03kg

Sealed cable-to-cable connector for auxiliary wiring, sensors and low-current DC circuits.
12V, 24V, 36V and 48V DC systems
High-current loads above 13A per contact

Q: What is a Deutsch DT connector?
DT is the most common Deutsch family of sealed automotive connectors, originally speced by heavy-truck OEMs. Two mating halves with silicone seals, a secondary wedge lock, and stamped-formed size-16 terminals give a factory-quality cable-to-cable join anywhere on the vehicle.

Q: Can I use this for both power and signal lines?
Yes. Each contact is rated 13A, so 6 circuits can carry any mix of signal and low-current power up to 13A per pin. Steady total across all 6 pins in a hot engine bay derates to around 8 to 9A each.

Q: What wire size fits the terminals?
Size-16 stamped contacts accept 0.5 to 1.5mm² conductor (roughly 20 to 16 AWG).

Q: Can I use a generic open-barrel crimper?
No. Deutsch stamped contacts need a Deutsch-pattern indent crimper set to size-16. Open-barrel automotive crimpers mash the terminal and prevent it from seating in the housing.

Q: Can these be used in marine environments?
Yes. IP68 rating and corrosion-resistant materials make them suitable for marine and outdoor use, including sustained wet exposure below the waterline in enclosed spaces.

Q: What does IP68 mean here?
Dust-tight and rated for continuous submersion past 1m per IEC 60529. Seals only hold when the connector is fully mated and every unused cavity is plugged.

Q: Is this kit reusable?
Yes. With a Deutsch pin-extraction tool, contacts release from the housing and re-crimp onto new wire.

Q: Can I use it on a 24V or 48V system?
Yes for 12V, 24V, 36V and 48V DC, within the 13A per-contact limit.

Join our community.